top of page

Old Town AutoPilot Rigging Layout: Deck, Tools, Bait and Battery

Nov 9
3 min read

Updated: Nov 12

A clean Old Town AutoPilot rigging layout puts everything you reach for often within arm's reach, and everything else out of the way. The command platform holds your fish finder and controls up front, tool holders keep pliers and scissors at your side, the bait rack keeps bait off the deck and drying, and the battery monitor mounts keep your power readings visible without a tangle of wires. The trick is to build the layout around how you fish, not around how much gear you own.


Start With the Command Platform


Every layout starts at the front. The DeckClear Command Platform for Autopilot gives your fish finder and controls a home right where you can see and reach them, and it costs $97.95. With the electronics up on the platform, the deck in front of you stays clear for landing fish and handling gear. Mount it once, set your screen angle, and stop shuffling gear to make room.


DeckClear Command Platform for Autopilot, installed on the kayak with a fish finder
DeckClear Command Platform for Autopilot

Tools Within Reach, Not Underfoot


Pliers, scissors and hook tools are the things you grab a dozen times a trip, so they belong at your side, not under your seat. The ToolNest Mini, at $35.95, holds the small essentials, and the ToolNest XL, at $42.95, takes the bigger load when you carry more. A tool in a holder is a tool you can find with one hand, even when a fish is in the net.


ToolNest Mini, mounted on the kayak holding small tools
ToolNest Mini

ToolNest XL, mounted on the kayak holding pliers and scissors
ToolNest XL

Bait Off the Deck


Bait on the deck is a mess waiting to happen: it slides, it smells, and it gets underfoot. The DryDock Bait Rack for Autopilot holds bait up and out of the way while it dries, and it costs $31.95. Your deck stays clean, your bait stays where you put it, and you are not clearing a spot every time you rebait.


DryDock Bait Rack for Autopilot, mounted on the kayak deck with lures hanging to dry
DryDock Bait Rack for Autopilot

Battery Monitors Where You Can See Them


Your battery is the heart of an AutoPilot, and you should not have to guess at it. The Battery Monitor Case Dual Pod, at $32.95, and the Triple Pod, at $34.95, mount your battery monitor in the shade where you can read it from the seat. Pick the pod that fits your monitor and your display setup, then check it the way you check your fuel gauge, at a glance.


Battery Monitor Case Dual Pod, open case showing the interior pods
Battery Monitor Case Dual Pod
Battery Monitor Case Triple Pod, installed on the kayak with three round battery monitors
Battery Monitor Case Triple Pod

Keep the Wiring Tidy

The last step is the one most anglers skip: wiring. Run cables along the platform and the track instead of across the deck, and keep each cable short and secured. Loose wire snags rods, feet and nets, and it makes a clean layout look cluttered. A tidy deck is a deck you can fish from without thinking about your feet.


FAQ


What should go on the command platform?


Your fish finder and the controls you use most. The DeckClear Command Platform for Autopilot keeps them up front, visible and reachable, so the deck stays clear.


Can I add tool holders later?


Yes. The ToolNest Mini and ToolNest XL mount to the deck, so you can start with one and add the other as your kit grows.


How do I keep the deck clear with so much gear?


Give every item one home and keep it there. Platform for electronics, holders for tools, rack for bait, mounts for the battery monitor, and nothing loose on the deck.

 
 
 

Recent Posts

See All
How to Mount a Fish Finder on a Kayak

A fish finder only helps if you can read it. A screen buried at your feet, flopping on a loose arm, or washed out by sun is dead weight. Getting the mount right is a one-time job that pays off every t

 
 
 

Comments


bottom of page